A symmetric rotating magnetic field can be produced with as few as three coils. Three coils will have to be driven by a symmetric 3-phase AC sine current system, thus each phase will be shifted 120 degrees in phase from the others. For the purpose of this example, magnetic field is taken to be the linear function of coil’s current.
The result of adding three 120-degrees phased sine waves on the axis of the motor is a single rotating vector. The rotor (having a constant magnetic field driven by DC current or a permanent magnet) will attempt to take such position that N pole of the rotor is adjusted to S pole of the stator’s magnetic field, and vice versa. This magneto-mechanical force will drive rotor to follow rotating magnetic field in a synchronous manner.
A permanent magnet in such a field will rotate so as to maintain its alignment with the external field. This effect was utilised in early alternating current electric motors. A rotating magnetic field can be constructed using two orthogonal coils with 90 degrees phase difference in their AC currents. However, in practice such a system would be supplied through a three-wire arrangement with unequal currents. This inequality would cause serious problems in standardization of the conductor size and to overcome it, three-phase systems are used where the three currents are equal in magnitude and have 120 degrees phase difference. Three similar coils having mutual geometrical angles of 120 degrees will create the rotating magnetic field in this case. The ability of the three phase system to create a rotating field utilized in electric motors is one of the main reasons why three phase systems dominated in the world electric power supply systems. Because magnets degrade with time, synchronous motors and induction motors use short-circuited rotors (instead of a magnet) following a rotating magnetic field of multicoiled stator. (Short circuited turns of rotor develop eddy currents in the rotating field of stator which (currents) in turn move the rotor by Lorentz force).
Note that the rotating magnetic field can actually be produced by two coils, with phases shifted 90 degrees. In case two phases of sine current are only available, four poles are commonly used. wikipedia

Alternators generate electricity by the same principle as DC generators, namely, when the magnetic field around a conductor changes, a current is induced in the conductor. Typically, a rotating magnet called the rotor turns within a stationary set of conductors wound in coils on an iron core, called the stator. The field cuts across the conductors, generating an electrical current, as the mechanical input causes the rotor to turn.
The rotor magnetic field may be produced by induction (in a “brushless” alternator), by permanent magnets (in very small machines), or by a rotor winding energized with direct current through slip rings and brushes. The rotor magnetic field may even be provided by stationary field winding, with moving poles in the rotor. Automotive alternators invariably use a rotor winding, which allows control of the alternator generated voltage by varying the current in the rotor field winding. Permanent magnet machines avoid the loss due to magnetizing current in the rotor, but are restricted in size, owing to the cost of the magnet material. Since the permanent magnet field is constant, the terminal voltage varies directly with the speed of the generator. Brushless AC generators are usually larger machines than those used in automotive applications.A rotating magnetic field is a magnetic field which periodically changes direction. This is a key principle to the operation of alternating-current motor. In 1882, Nikola Tesla identified the concept of the rotating magnetic field. In 1885, Galileo Ferraris independently researched the concept. In 1888, Tesla gained U.S. Patent 0,381,968 for his work. Also in 1888, Ferraris published his research in a paper to the Royal Academy of Sciences in Turin. Wikipedia

Alternators are used in modern automobiles to charge the battery and to power the electrical system when its engine is running. Until the 1970s, automobiles used DC dynamo generators with commutators. With the availability of affordable silicon diode rectifiers, alternators were used instead. Alternators have several advantages over direct-current generators. They are lighter, cheaper and more rugged. They use slip rings providing greatly extended brush life over a commutator. The brushes in an alternator carry only excitation current, a small fraction of the current carried by the brushes of a DC generator, which carry the generator’s entire output. A set of rectifiers (diode bridge) is required to convert AC to DC. To provide direct current with low ripple, a three-phase winding is used and the pole-pieces of the rotor are shaped (claw-pole) to produce a waveform similar to a square wave instead of a sinusoid. Automotive alternators are usually belt driven at 2-3 times crankshaft speed. The alternator runs at various RPM (which varies the frequency) since it is driven by the engine. This is not a problem because the alternating current is rectified to direct current.

Typical passenger vehicle and light truck alternators use Lundell or claw-pole field construction, where the field north and south poles are all energized by a single winding, with the poles looking like fingers of two hands interlocked with each other. Larger vehicles may have salient-pole alternators similar to larger machines. There are two separate types of alternators. The Delta set-up and the Wye set-up. 
Automotive alternators require a voltage regulator which operates by modulating the small field current to produce a constant voltage at the battery terminals. Early designs (c.1960s-1970s) used a discrete device mounted elsewhere in the vehicle. Intermediate designs (c.1970s-1990s) incorporated the voltage regulator into the alternator housing. Modern designs do away with the voltage regulator altogether; voltage regulation is now a function of the electronic control unit (ECU). The field current is much smaller than the output current of the alternator; for example, a 70 A alternator may need only 7 A of field current. The field current is supplied to the rotor windings by slip rings. The low current and relatively smooth slip rings ensure greater reliability and longer life than that obtained by a DC generator with its commutator and higher current being passed through its brushes.
The field windings are initially supplied power from the battery via the ignition switch and “charge” warning indicator (which is why the indicator is on when the ignition is on but the engine is not running). Once the engine is running and the alternator is generating power, a diode feeds the field current from the alternator main output equalizing the voltage across the warning indicator which goes off. The wire supplying the field current is often referred to as the “exciter” wire. The drawback of this arrangement is that if the warning lamp burns out or the “exciter” wire is disconnected, no current reaches the field windings and the alternator will not generate power. Some warning indicator circuits are equipped with a resistor in parallel with the lamp that permit excitation current to flow if the warning lamp burns out. The driver should check that the warning indicator is on when the engine is stopped; otherwise, there might not be any indication of a failure of the belt which may also drive the cooling water pump. Some alternators will self-excite when the engine reaches at a certain speed.
Older automobiles with minimal lighting may have had an alternator capable of producing only 30A. Typical passenger car and light truck alternators are rated around 50-70A, though higher ratings are becoming more common, especially as there is more load on the vehicle’s electrical system with air conditioning, electric power steering and other electrical systems. Very large alternators used on buses, heavy equipment or emergency vehicles may produce 300 amperes. Semi-trucks usually have alternators which output 140A. Very large alternators may be water-cooled or oil-cooled.
In recent years, alternator regulators are linked to the vehicle’s computer system and various factors including air temperature obtained from the intake air temperature sensor, battery temperature sensor and engine load are evaluated in adjusting the voltage supplied by the alternator.
Efficiency of automotive alternators is limited by fan cooling loss, bearing loss, iron loss, copper loss, and the voltage drop in the diode bridges. At partial load efficiency is between 50-62% depending on the size of alternator and varies with alternator speed. This is similar to very small high-performance permanent magnet alternators, such as those used for bicycle lighting systems, which achieve an efficiency around 60%. Larger permanent magnet alternators can achieve higher efficiencies.[citation needed] Large AC generators used in power stations run at carefully controlled speeds and have no constraints on size or weight. They have much higher efficiencies, as high as 98%.
Hybrid automobiles replace the separate alternator and starter motor with one or more combined motor/generator(s) (M/Gs) that start the internal combustion engine, provide some or all of the mechanical power to the wheels, and charge a large storage battery. When more than one M/G is present, as in the Hybrid Synergy Drive used in the Toyota Prius and others, one may operate as a generator and feed the other as a motor, providing an electromechanical path for some of the engine power to flow to the wheels. These motor/generators have considerably more powerful electronic devices for their control than the automotive alternator described above. Wikipedia

Alternators generate electricity using the same principle as DC generators, namely, when the magnetic field around a conductor changes, a current is induced in the conductor. Typically, a rotating magnet, called the rotor turns within a stationary set of conductors wound in coils on an iron core, called the stator. The field cuts across the conductors, generating an induced EMF (electromotive force), as the mechanical input causes the rotor to turn.
The rotating magnetic field induces an AC voltage in the stator windings. Often there are three sets of stator windings, physically offset so that the rotating magnetic field produces a three phase current, displaced by one-third of a period with respect to each other.
The rotor’s magnetic field may be produced by induction (as in a “brushless” alternator), by permanent magnets (as in very small machines), or by a rotor winding energized with direct current through slip rings and brushes. The rotor’s magnetic field may even be provided by stationary field winding, with moving poles in the rotor. Automotive alternators invariably use a rotor winding. Wikipediacitation needed], which allows control of the alternator’s generated voltage by varying the current in the rotor field winding. Permanent magnet machines avoid the loss due to magnetizing current in the rotor, but are restricted in size, due to the cost of the magnet material. Since the permanent magnet field is constant, the terminal voltage varies directly with the speed of the generator. Brushless AC generators are usually larger machines than those used in automotive applications.
An automatic voltage control device controls the field current to keep output voltage constant. If the output voltage from the stationary armature coils drops due to an increase in demand, more current is fed into the rotating field coils through the voltage regulator (VR). This increases the magnetic field around the field coils which induces a greater voltage in the armature coils. Thus, the output voltage is brought back up to its original value.
Alternators used in central power stations may also control the field current to regulate reactive power and to help stabilize the power system against the effects of momentary faults.

Kali ini kita akan membedakan OH 1526 and OH 1626 dari segi stabilizer dan suspensi yang menyangga badan bus Mercedes Benz ini, berikut ulasan perbedaan berdasarkan suspensi.

Stabilizer OH-1526 terbuat dari baja batangan utuh yang dibending. Suspensinya memakai trapezoid leafspring yang lengkungnya negatif. Stabilizer OH-1626 pada bagian arm-nya terbuat dari besi pelat yang disambung dg tubular steel. Suspensinya memakai Air Suspension yang langsung menyangga chassis utama (seperti Volvo B7R), Tidak seperti SCANIA K-Series atau Air Suspension rakitan Adi Putro yang menyangga cross member. Air Suspension OH-1526 memakai 2 stabilizer (kiri & kanan). Untuk Air Suspension yang menyangga crossmember (SCANIA K Series, Airsus rakitan AP, OH-1830) stabilizernya ada 4.

mungkin di antara rekan belum tahu bagaimana cara mengganti DNS dari modem yang rekan pakai, berikut edikit tips dan trik cara mengganti DNS Smartfreen supaya koneksi lebih cepat dan stabil. Mengapa DNS perlu di rubah, DNS di rubah sebagai cadangan saja barangkali DNS punya provider sedang dalam keadaan error jadi kita tetap bisa mengakses internet. Atau, kalau DNS punya provider anda lebih lambat maka dengan DNS ini akses akan lebih cepat. Begini cara menggati DNS Smartfreen